RoadChem™ 301® Slurry Quickset®

RoadChem™ 301® Slurry Quickset

VSS ASPHALT TECHNOLOGIES DATA SHEET VER: 1.0 --PRODUCT INFORMATION

Back to Specialty Chemicals Page

DESCRIPTION:
RoadChem™ 301® is a cationic emulsifier for the manufacture of asphalt emulsions for slurry and coarse graded cold mix applications. RoadChem™ 301® is designed to suit especially for highly reactive aggregates that have adhesion problems. The emulsifier provides extended mixing times to ensure coating and the controlled chemical break allows rapid build up of cohesion after mixing.

BENEFITS:

Stability
Easy to handle and transport
Quick traffic
Wider range of compatibility with aggregates
Extended mixing times to ensure coating

PHYSICAL PROPERTIES:
Appearance: Liquid
Flash point (Closed Cup): (C) >140
Pour Point: (C) 12C
Specific gravity: 25C 1.01kg/lt
Viscosity, cps 25C: >50,000
Boiling Point (C): 110C
Actives: 100%
Storage life: Min 12 months in drums or bulk. (30-50C in covered area in sealed drums)

APPLICATION:
RoadChem™ 301® may be used with a range of different polymer modification including Neoprene, SBR, EVA, EMA and SBS.
RoadChem™ 301® should be kept at 80C or higher prior to use for pumping. It should not be stored at above 60C.
RoadChem™ 301® can be easily neutralized with hydrochloric acid (concentrated). It is good practice to acidify the water before addition of RoadChem™ 301®.

TYPICAL FORMULATION:
All formulations should be tested in the laboratory before use.

Slurry Seal Quick Set:
Asphalt: 62-63%
Soap (based on total emulsion by weight)
RoadChem™ 301®: 1.2-1.8%
Concentrated HCI (pure): to pH 1.5-2.8
Water to 100%

Slurry Seal Polymer Modified:
Asphalt: 62-63%
Soap (based on total emulsion by weight)
RoadChem™ 301®: 1.0-1.8%
Concentrated HCI (pure) to pH 1.8-2.5
Latex (60% solids): 3-4.0%

Cold Mix Emulsion- Coarse Graded Mixes:
Asphalt: 60-65%
Soap (based on total emulsion by weight)
RoadChem™ 301®: 1.5-2.0%
Concentrated HC(pure) to pH 2.0-2

NOTES:
Note that RoadChem™ 301® should be added to warm water that has already had the acid added to it. The emulsifier buffers the solution so mix for at least 20 minutes before testing pH.

Note also that slurry and microsurfacing emulsions must be designed relatively to the mixture. That is a full ISSA mixture design must be done to verify performance.

Notes:

RoadChem™ 301®: may be blended with RoadChem™ 301® to improve adhesion and extend mixing times of RoadChem™ 301® slurry emulsions.
RoadChem™ 301®: may be used with a wide range of retarders including aluminum sulfate, ammonium chloride, JP4, borax, and may be used in the prewet water in a neutralized solution of 5% as a retarder.
RoadChem™ 301®: has a high viscosity at low temperatures, store at 60C and heat to up to 90C for short periods to allow pumping.
RoadChem™ 301®: neutralizes easily, The ratio of HCI RoadChem™ 301®: to achieve required pH is about 0.4.
Prolonged exposure of RoadChem™ 301® to moisture or carbon dioxide will reduce its activity. As far as possible use only Rill drums.
Latex should be co-milled into the emulsion for the best dispersion, emulsion stability and control of the final properties of the slurry. Latex may be post added or added into the soap if no co milling is not available.

SAFETY:
Contains alkaline corrosive materials. Will cause eye and skin irritation if significant contact is made. Use goggles, gloves and protective clothing when handling. Refer to the MSDS for further information.

Valley Slurry Seal Company, PO Box 981330, West Sacramento, CA 95798, USA.
Phone (916) 373-1500 Fax: (916) 373-1438 Email: vss@slurry.com

Information given herein is given in good faith, without warranty, representation or inducement or license of any kind. VSS does not assume any legal responsibility for reliance upon same. VSS is not responsible for materials not manufactured by VSS that may represent a hazard in handling or use, nor for the safety of any process employing any VSS product. No representation is given as to freedom from patent restriction.

RK/August 5, 1998